Skip to content
  1. Free Shipping on Orders over $75 | Home of Enduro Plasticsâ„¢

Modifications for Enduro Engineering Saw Mount Installation Instructions

Required Tools: 1/8", 9/32, and 3/8" drill bits or equivalent, de-bur tool, drill, masking tape (optional), permanent marker, 3mm and 4mm Allen wrench, 10mm and 13mm socket and ratchet, 13mm wrench, phillips screwdriver, rigid ruler or square, black paint. Tools listed are used if you bought all the mods. see directions for tools for each job.

Warning! Sharp tools are used in this installation. Take proper precautions to prevent injury!

Fork Mounts:

  1.  Remove the old fork mounts from the saw mount.
  2. Using the 4mm Allen and 10mm socket, install the new mounts with the slotted spacer in the basket slot. The Two-part mount is used as a cable guide for your front brake line. See Image #1
  3. Mount the assembly to your forks using the 13mm wrench and socket. 
  4. IMPORTANT NOTE! Any time  you re-install the saw mount on the bike, you will need to put anti-seize on the stainless 8mm bolts. Anti seize is already on the bolts for the first installation.
  5. Go get dirty!
#1 Fork Mounts
Saw Pads:
  1. Remove the block that sits under the saw and the bar guide.
  2. Install provided bar guide using the provided screws and Phillips screwdriver (you can still use the scabbard EE provided).
  3. Place the thicker bottom pad on the bottom of the aluminum and line up the two countersunk holes in the bottom of the mount. 
  4. Use a straight edge to make sure the pad is square with the front of the mount.
  5. Use the pad as a drill guide and drill 1/8" holes for the two corners of the pad that do not have a hole.
  6. Once you are satisfied with hole placement, upsize all the holes to 3/8".
  7. Debur holes so the rubber towers are not damaged.
  8. Paint the holes for corrosion resistance.
  9. Lubricate the towers on the pad and insert them into the holes.
  10. Place the back pad onto the back of the aluminum in a place where it makes the most contact with your saw.
  11. Repeat this process starting at step 5 for all four holes.
  12. Go get dirty!
#2 Base Pad
#2 Back Pad
Light Bar:
  1. Install the mounts on the light with the 3mm Allen wrench and provided screws.
  2. place the light bar in under the basket just behind the EE logo (make sure it doesn't hit your fender).
  3. Line up the mount with the edge of the basket so it points straight down the trail.
  4. Mark the mount locations for the light mounts using a sharpie.
  5. Pilot drill the mount locations and hold the light assembly up to verify the holes are in the right spot. The holes are 6.532" apart.
  6. Up size the holes to 9/32".
  7. Install the mount with the provided screws using the 4mm Allen wrench.
  8. Plug it in! (if you  have the SAE version, please refer to our light bar installation instructions for wiring and switch location)
  9. Use the 3mm Allen to adjust the light beam.
  10. Go get dirty in the dark!

#3 Light Bar

Bottle Sides

  1. Install the bottom plates with the supplied hardware using the 4mm Allen wrench and 10mm socket. The back bolt goes in the round hole and the front bolt goes in the bottom of the front, curved slot.
  2. Remove the saw strap and install the side plates with the supplied hardware using a 4mm Allen wrench and 10mm socket. (The top hole is where the factory strap is re-installed)
  3. Install the rubber straps on the printed tabs.
  4. Add your 3" diameter or smaller  bottles. We recommend the smaller oil bottle be mounted on the saw bar side for good balance.
  5. Got get dirty!

#4 Bottle Mounts

Ride Fearless. Ride Smarter. Ride Longer.

We started making motorcycle parts for ourselves because we wanted something better. Now we want to provide something better for you too!

Ride with confidence. Ride with 3DC Moto Parts.

A rider-centric approach to off-road motorcycle parts, offering high-quality, American-made products designed to enhance your riding experience.

Offering all of our cool stuff to you.

3DC Moto provides a rider-centric approach to off-road motorcycle parts, offering high-quality, American-made products designed to enhance your riding experience.

We combine expert engineering with a passion for the sport, delivering durable, performance-enhancing parts using our trademarked Enduro Plastics™ at competitive prices. 

All backed by fast shipping and exceptional customer service.  3DC Moto offers products with superior durability and protection, ensuring your bike can handle the toughest trails. 

Vision

We love to ride! We love to build things! And our goal is to offer premium protection for critical offroad motorcycle parts.

Mission

With 3DC Moto, you gain more than just parts; you gain a partner who is as invested in your riding experience as you are. Let us help you take your riding to the next level.